The click takes the point by the ground clicked, then the piece or the junction under the cursor; the point nearest on the
screen only when there's none, no farther than what is under the cursor and a bit beyond it, by whole pixels first and
the range then, so the order of the roads doesn't decide. The ends of the pieces are gone through without looking for the
repeated ones (editor_road::each_joint), joints() isn't needed. Esc, the road window closed, another tool or the track work
area drop the drag; Ctrl+Z and Ctrl+Y wait for its end.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01DDcMn1Q7wdYkbxDUWscNHZ
The points where the pieces of a road meet were picked only by the ground clicked: one more than 3 m above or below the
ground under the cursor (a road taken down into a cutting, under an embankment) couldn't be picked again. Now the point
nearest to the cursor on the screen (within 12 px, the one nearer to the camera of those about as near) is picked first,
the ground as before after it.
Alt+LMB on a point and dragging up or down changes the height of the selected points (Ctrl: ten times finer); the change
shows as yellow lines and a label by the cursor while dragging, and is applied, as one step of the history, when the button
is let go.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01DDcMn1Q7wdYkbxDUWscNHZ
The side sway from the lateral acceleration now goes off only on a track with a sideways value, and the random jolts on one with a vertical or a sideways value. Dips at the rail joints and cross level alone replace neither. On a switch it goes by the path set and what its joined tracks allow.
An edit in the editor also rebuilds the other switches of a joined group with the tracks they meet, and the tracks of a rail run whose joints moved. Removing a track does the same. While dragging, the tracks further off wait until the drag ends.
The clatter of a bogie's axles was right: the followers stand at the pivots and the offsets are the places of the wheel sets. The misleading name goes.
Also what Sonar had left: a parameter as a span, a const method, a struct and its member apart, commented out code, and a function of the grading tool split, with the same output.
Its numbers go by position, and the positions differ between a plain track
and a switch. A switch made in the style of a plain track wrote them in the
layout of the plain one, so they were read back as other values: the up and
down part as the value of the path p3-p4, and so on.
The values are now one struct with pure functions to read, write and resolve
them, which replaces eight fields and which the unit tests can reach.
Usage, before endtrack, in mm, 0-100, separated by semicolons with no
spaces:
a plain track: uneven value;up;side;cross;dip
a switch: uneven p1-p2;p3-p4;up p1-p2;side p1-p2;up p3-p4;side p3-p4
uneven 18 the value alone
uneven 18;;;25;6 with its own cross level and dip at the joints
uneven 0;;30 sideways alone
uneven 14;35 a switch, 14 on the straight path, 35 on the diverging
What's left out takes the first number, the dip goes by the up and down
one, and a path p3-p4 with no numbers of its own takes those of p1-p2.
This replaces unevenup, unevenside, unevencross and jointdip. The fields
in the editor stay, track panel, section Ride and sound.
At the end they share, the paths of a switch keep to the lower value, and
each comes to its own value along the way. Joined switches take the lowest
of the same path, a path joined to another path the lower of the two, and
a plain track comes to the value of the path it meets. See
track_uneven_doc.md.
Usage, optional attributes of a track entry, before endtrack:
uneven <mm> peak deviation of a rail on a 10 m chord, 0-100; normal and switch
unevenup <mm> up and down alone, instead of uneven; normal and switch
unevenside <mm> sideways alone, instead of uneven; normal and switch
unevencross <mm> cross level alone, instead of uneven; normal only
jointdip <mm> depth of the dip at rail joints, every sound distance; normal only,
default 0.4 of the up and down component
Values of uneven follow PLK Id-14 appendix 1: 6 mm is the limit at 160 km/h, 10 at 120,
18 at 80, 35 at 40; half of it for a track in a good state. Example:
uneven 18
unevencross 25
jointdip 6
endtrack
The same fields are in the editor, track panel, section Ride and sound. See
track_uneven_doc.md.
The unevenness is a displacement field over the plan of the scenery, with no random
numbers: one place strays the same every time, and joined tracks, the paths of a switch,
sleepermodel and axles at one place move together. Tracks meet at a joint at the lower of
their values. Joined switches take the lowest of theirs, the tracks joined to them come to
it, and a track with none of a component keeps the switch to its design in it. The clatter
comes from the dipping joints. Curve radius and grade for the physics stay as designed.
Tracks with it get geometry every 2 m on straights: 4x the vertices on Baltyk with all
tracks flagged, 0.2 ms more per frame on td.scn.
- Terrain work mode shows a browser of the textures folder in place of the
node bank; textures/materials can be dragged onto the palette entries
(replacing the material), the material field and the water material field
- Ctrl+Z/Ctrl+Y for heightmap terrain changes: a brush stroke or an
operation is one step of the editor history
- Ground conversion reads only the files of the terrain directives
(.txtf with origin/rotate, or .btf without text), paints the chunks with
the materials of the triangles, drops only the shapes of those files
- Fix: ground grids converted out-of-range floats to int, so whole-scene
queries returned the triangles of a single cell (shifted chunks)
- Fix: terrain layers copied from textures already uploaded without their
data stayed grey
- Fix: ImGui ID conflict between terrain tool radios and section headers
- Fix: layers of terrain .txtf files named with the scenery/ prefix and
could not be saved
- Editor selftest commands for the terrain