- radioon_sw:/radiooff_sw:/radiofuseon_sw:/radiofuseoff_sw: are now loaded
as push-button gauges in initialize_gauge, so they can be clicked; the
enable/disable commands press them while held. radiotoggle and
radiofusetoggle flip the state directly, so they don't move them.
- New driver hint "Close radio fuse" (radiofuseon); "Switch on radio" is
given only when the radio's own switch is off.
- The HUD shows the radio channel only with the fuse closed.
(eu07/maszyna#438)
Both waited for every vehicle of the scenery to stand still, so on a scenery
with AI traffic a test could pass only when the traffic happened to stand too,
and the standstill end hardly ever came.
A test scenery names the train under test with test.vehicle <name> in its
config block (once for each train, if several): the pass and the standstill wait
for the consists of these vehicles as they are at the moment, so a train the
tested one couples to counts with it. A name the scenery doesn't have ends the
test with the error code. Without test.vehicle every vehicle counts, as before.
A signal passed at danger counts for every train either way.
run.py puts the case's lead vehicle into test.vehicle. test_mode_standstill_traffic
has the train under test standing on track 2 of Stacja1 while AI traffic leaves
track 1 on the timetable: it ends on its 100 s standstill, where counting every
vehicle runs into the 300 s timeout. Physicslogs of the other trains of a case
(<something>_<vehicle>) are moved out of the game dir too.
A test run that hung, in the loading or anywhere else, waited until whoever
started it killed it. A watchdog thread now ends a run still going test.wall_timeout
seconds of real time after the start of the simulator, loading included: it says
`test: timeout ... still running after N s of real time` and quits with the
timeout code, whatever the main thread is doing, with no dialog. A test that has
ended but whose simulator doesn't close ends with its own result.
The limit is test.wall_timeout (settings, the scenery's config block) or
--test-wall-timeout, which wins. Not given, it is test.timeout + 600 s: ten
minutes for the loading, and a simulation that runs at least as fast as real
time is never cut short. test.timeout 0 means no watchdog unless the limit is
given; test.wall_timeout 0 turns it off.
run.py passes the case's timeout as --test-wall-timeout and kills a simulator
only 30 s after it. A timeout from the watchdog counts as wall_timeout there, so
a run that hung doesn't pass a case expecting the simulation time to run out;
test_mode_wall_timeout ends while loading on a limit of 2 s.
The log was printed in colour to stdout too (debuglog bit 2), so a script reading
the verdict of a test got the whole log with it. In test mode the log goes to the
log file only and stdout has the `test: ...` line alone; the usage text of a bad
command line goes to stderr. Whether the run is a test is now known before the
log service starts.
- TController::TableCheck() calls TSpeedPos::Update() as it did before the
test mode: the check for a signal passed at danger is a call of its own
after it (CheckSignalPassedAtDanger), so the update lines nest no deeper
than on master (S134). A switch is a track, so a signal's update never
takes the switch-change branch and the check runs in the same place as
before; the physicslogs of all 15 scenario cases are byte for byte the
same.
- null_imgui_renderer is final (S1235), to_string(test_result) uses
`using enum` (S6177), init_result_cell() is const (S5817),
ConfigParseTest() takes a std::string_view (S6009) and the test settings
struct is declared apart from its member (S3646).
In vehicles like the ST43, the SP32 or the SN61 every engine of a train in
multiple has its own start and stop buttons in the cab. Until now the cab's
line breaker / engine start switch (main_sw, main_on_bt, main_off_bt) always
started and stopped the engines of all the vehicles under its control.
- .fiz, Engine: JointEngineStart=Yes|No (default Yes, as before). With No
the cab's main_* work the cab's own vehicle only, and an engine stopping on
its own (stalled, out of fuel) stops only its own vehicle instead of every
engine in the train.
- .mmd: mainb_sw, mainb_on_bt, mainb_off_bt work the second vehicle with an
engine under the cab's control, mainc_sw, mainc_on_bt, mainc_off_bt the
third one. They count along the control cable from the cab's vehicle,
behind the cab first. Like main_*, the start switch has to be held for the
vehicle's IniCDelay with the vehicle ready (MainSwitchCheck); an impulse
switch of an electric locomotive with series motors closes on release.
- New commands, added at the end of the command list: linebreakertoggleb,
linebreakeropenb, linebreakercloseb, linebreakertogglec, linebreakeropenc,
linebreakerclosec. No default keys.
- The logic is in vehicle/enginestart.{h,cpp} (core library), tested in
tests/unit/test_engine_start.cpp.
Nothing changes for existing vehicles: the new key and the new cab controls
are optional, and without them the code does what it did before.
Game data (SVN, not changed here, to be done separately; the code works
without it): for the SN61 (dynamic/pkp/sn61_v2), whose cab models already
have the buttons start02/stop02/start03/stop03,
- sn61.fiz, sn61-86.fiz, sn61_v1.fiz and the other SN61 .fiz: add
JointEngineStart=No to the Engine: line;
- sn61.mmd.inc (and the other SN61 includes): after main_on_bt add
mainb_off_bt: { stop02 mov -0.005 0 0.1 ... }
mainb_on_bt: { start02 mov -0.005 0 0.1 ... }
mainc_off_bt: { stop03 mov -0.005 0 0.1 ... }
mainc_on_bt: { start03 mov -0.005 0 0.1 ... }
with the sounds of main_off_bt / main_on_bt.
The tooltips "line breaker B" / "line breaker C" are new strings for lang/*.po.
TMoverParameters::RadioFuse, closed by default, stands for a fuse in the
cabinet, a lever on the desk or the switch on the radio's power supply.
RadioPowered() needs it closed, so with it open the radio's buttons, calls,
messages and the radio-stop stop working; opening it at a standstill resets
the radio-stop as switching the radio off does, and the radio and radio-stop
lamps go out. New commands radiofusetoggle/radiofuseenable/radiofusedisable
(no default keys), cab controls radiofuse_sw: (follows the fuse state),
radiofuseon_sw: and radiofuseoff_sw:, and radio_fuse for the Python screens.
The AI turning the radio back on closes the fuse too.
Existing vehicles don't change: the fuse starts closed and opens only from a
new cab control or a bound key. SVN data, optional: cabs that have such a
fuse or lever get one of the new controls in their .mmd, in the form of
radio_sw: (e.g. "radiofuse_sw: { <submodel> rot 0 0 0 }"); lang/*.po can
translate "radio fuse".
(eu07/maszyna#438)
An electric and a diesel locomotive got their control coupled whenever the
scenario (and so the Starter) asked for it, since the scenery coupling ignores
ControlType, or when neither coupler named a control system, so a Vectron and
an SM42 ran in multiple unit.
TMoverParameters::Attach() now leaves the control connection out between an
electric (ElectricSeriesMotor, ElectricInductionMotor) and a diesel
(DieselEngine, DieselElectric/DumbDE) traction vehicle, for the scenery, the
AI, the coupling keys and the automatic couplers alike, and logs it. Vehicles
without own traction (cars, control trailers) are not affected, nor are
permanent couplings within a unit, nor couplers that both name the same
ControlType, which stays the vehicle authors' way to allow such a pair. The
AI coupling order expects the coupling the vehicles can take, so it doesn't
wait for the control connection forever.
Existing scenarios coupling such a pair still load, without the control
connection. "controlcoupling.enginecheck no" in eu07.ini turns the check off.
No SVN data change is needed. (eu07/maszyna#520)
The config key from eu07/maszyna#541. By default (yes) a pass reported to
__test.result waits until every vehicle has stood still for 1 s; with no it
ends the test at once. The key is listed with the other test.* settings in the
log and in the test start line.
Scenario tests: new case test_mode_pass_while_moving reports the pass from
event2 of tor1k as the train runs onto it and checks the run ended with the
train still moving (new check ends_moving). The README lists the test.* keys
with their defaults and the input the test mode ignores.
The test manager is reached through simulation::test() instead of a global,
the result cell is owned by a unique_ptr until the memory table takes it, the
cell value is compared with a margin, strings are built with std::format and
the --test settings moved to apply_test_mode_settings(). The driver's signal
check is folded into UpdateSpeedPosition(), which updates a speed table entry
and reports a signal at stop the head of the train just passed. The test.*
keys are listed with the other settings at the start of the log.
eu07 --test -s <scenery> [--test-timeout <s>] runs the scenery in ghostview with
the null renderer (models loaded, no textures), a hidden window, no sound,
network or python, and in fixed steps of 0.03 s of simulation time per frame
(three 10 ms physics steps) as fast as it can. Without -seed it uses a fixed
seed, so two runs give byte-identical physicslogs.
The scenery reports its result to the __test.result memory cell, which the
simulator always creates: value 1 passes once every vehicle has stood still for
1 s, value 0 fails at once. The run ends with exit code
0 pass, 1 fail,
2 a train passed a signal at stop (SetVelocity 0 0, as seen in its driver's
speed table; SetVelocity 0 x on automatic block doesn't count),
3 timeout (test.timeout, default 3600 s of simulation time),
4 standstill (every vehicle still for test.standstill s, default 300, with no
result; a pass with test.pass_on_standstill yes),
5 error (no -s, the scenery didn't load or has no vehicles, an exception).
The test.* keys go in the scenery's config block; test.fail_if_stop_overran no
only logs a signal passed at danger. Outside the test mode a signal passed at
danger is logged.
The null renderer gets a ui backend which draws nothing, hands out the null
texture and material instead of throwing, and ends the ui frame. A GL context
is still made for the hidden window, without asking for a version, as parts
of the ui create textures with gl calls of their own. No crash dialog or
message box in test mode; the window code no longer needs a monitor.
- the log stops through a flag kept in a function, not a global one
- the messages are put together with std::format
- a vehicle dropped on a trainset in the launcher goes in once the
trainset is drawn, so the vehicles are gone through with a plain loop
again; the drop split into a new vehicle and a moved one
- the scenario that can't be opened is caught as the runtime error it
is, a file name outside of the code page as the system error it is
- a track of an unknown type is left out through the pointer owning it
- the keyword of a track type written out by a function of its own
- the picked node forgotten with ranges::replace_if, the empty
Forget_Node of the base renderer told why it is empty
- FileCased takes the path it works on
utilities.cpp starts with a byte order mark, so the compiler reads it as utf-8. The game's targets don't get
/utf-8, though: set_target_properties(... COMPILE_OPTIONS ...) in the MSVC block of CMakeLists.txt replaces the
options add_compile_options gave them. So the string literals went into the program in the code page of the
system, windows-1250 on a polish one, and the map of win1250_to_utf8 turned each letter into itself.
What read windows-1250 through it got no utf-8: the names, descriptions and categories of the sceneries and the
names of the textures in the launcher, and the descriptions of the templates in the editor. The editor writes
such a description back through utf8_to_win1250, which makes a question mark of each byte that doesn't start
a utf-8 sequence, so the letters it had read unchanged didn't come back.
The utf-8 sequences are written as bytes now, the way utf8_to_win1250 has them, so they don't depend on the
options. The options stay as they are: with /utf-8 other literals of the files with a byte order mark would
change, the "±" of the table of Bezogonkow would take two bytes and move the letters after it.
The unit tests check the letters and that the text given is valid utf-8.
Co-authored-by: maj00r <maj00r@host>
A scenario failing past its opening popped the loader mode and went on to pop it again and push the driver mode with the scenery half loaded; it goes back to the launcher as one that can't be opened. FileCased() goes through the folder only where the file system tells the case apart: on Windows a missing file was looked for in its whole folder for nothing, and a name outside the code page threw from the parser. The Discord thread sleeps a quarter of a second outside the driver mode, not to hold the closing up.
The command line gives the name of the scenery lowercased, and the sceneries made on Windows name their files and includes in any case: on a case-sensitive filesystem they weren't found. FileCased() finds the file whose name differs only in case; the parser and the scenario loader use it. A scenario that can't be opened logs the reason and goes back to the launcher instead of ending with an exception.
The log service stopped with applicationQuitOrder, so whatever was logged while the simulator closed was lost; it now runs until StopLogService() and writes out what came before. The closing logs each of its steps with the time since it began, to tell where a closing that hangs stops. Outside the driver mode the Discord thread spun a core in its loop, it now sleeps a second between the checks.
* fix: automatic coupler crashes, horns, compressor start delay, radio and cab lever sounds
fix(cab): the line contactors lamp goes out with the pressure switch (eu07/maszyna#470)
The lamp of the open line contactors, which tells the start can be made, went out at 1 bar in the brake
cylinders, while the pressure switch cuts the start off only at 2 bar (or below 3.6 bar in the main pipe), so
with the brakes partly applied the start could be made with the lamp out. With a pressure switch fitted the lamp
now follows it; without one it goes out at 1 bar as before. The same holds for the lamp of the second unit, which
used to keep its last state between 1 bar and the cut-off. The condition is
TMoverParameters::LineContactorsLampLit().
Tests: tests/unit/test_line_contactors.cpp.
refactor: Sonar findings of PR 217
- horn_supply::pneumatic shadowed the pneumatic enumerator of the sound flags (cpp:S1117), it's horn_supply::air;
the supplies read with using enum (S6177),
- CouplerForce(): the automatic coupling refused or caught without another level of nested ifs (S134), the
same outcome: too fast, the coupling is locked; caught, coupled and locked; otherwise left to try again,
- CompressorCheck(): the power the compressor doesn't draw yet noted without a TODO (S1135),
- tests: the previous crash damage setting in an in-class initializer (S3230), the loops which stop early with
break rather than in their conditions (S886), the stand-ins of test::pair in a std::vector rather than an array
(S5945), units in the comments of the example without /* */ (S1103).
test: the cases the changes of the branch left without a test
- Cntrl.: BDelay1 to BDelay4 reach the brake delays (now through std::format), the default start types of the
ground and converter overload relays of a multiple unit and of other vehicles (out of the nested conditionals),
- the compressor: fed from the low voltage it waits from the low voltage coming on; the pressure switch stops it
above the cut-out pressure, without one the excess air is vented (the vented fraction rewritten),
- the horns: a vehicle without any air sounds as before, the threshold pressure, an electric horn on 110 V,
- the positions of a cab control below zero, and a control without position sounds.
refactor(cab): the kind of the train heating switch as a flag
Read once with the vehicle definition, rather than compared as text in each of the switch commands.
feat(cab): train heating switch springing back (MaSzyna-EU07/maszyna#85)
TrainHeating=[toggle]|impulse in the Switches: section of the vehicle definition makes the train heating switch
an unstable one: it goes up to switch the heating on, down to switch it off, and back to the middle once let go,
instead of staying where it was put. The position of such a switch isn't set from the heating state when the cab
is entered.
Tests: tests/unit/test_switches.cpp.
feat(sound): mirror sounds (MaSzyna-EU07/maszyna#84, eu07/maszyna#322)
The sound definitions of a vehicle (.mmd) take mirroropen: and mirrorclose:, played as a mirror sets off
unfolding or folding, and the locations section mirrors: <offset>... end, the offsets along the vehicle of the
mirror pairs, as for the doors (negative ahead of the centre), each pair at the sides of the vehicle. As the
animation, only the mirrors at the occupied cab sound. The start of a move is mirror_moves::motion in
vehicle/mirrors.h.
Tests: tests/unit/test_mirrors.cpp.
feat(cab): joint oil and fuel pump switch (MaSzyna-EU07/maszyna#81)
A cab control oilfuelpump_sw: switches both the oil and the fuel pump at once, with the new command
oilfuelpumptoggle (no key by default). As a two-state switch it turns both pumps off when both are on and both on
otherwise; as an impulse switch it's held to start them, like the separate pump switches. Its position follows
the pumps when the cab is entered.
refactor(editor): text fields filled without strncpy (MaSzyna-EU07/maszyna#112)
The last three strncpy calls Sonar flags (cpp:S5816), in the road and track editors, copy the text into the
ImGui field buffers with std::string::copy and terminate it right after; the text gets cut to the buffer as
before.
fix: automatic coupler crashes, horns, compressor start delay, radio and cab lever sounds
- automatic couplers don't catch above the safe collision speed (#86): with crash damage on they couple at a
closing speed of 15 km/h at most, a faster hit locks the coupling until the vehicles part and the collision
runs its course. On the way: CollisionVelocity() read a head-on 10 + 10 km/h as 14.1 km/h (quaternions turn
by half the angle), it's now taken from the touching ends; CollisionDetect() took the other vehicle's speed
the wrong way round for vehicles facing each other. Head-on hits now derail sooner, at the intended limit,
- a single horn lever can't sound both tones at once (eu07/maszyna#392),
- a skid ends once the vehicle stops on locked wheels (eu07/maszyna#479),
- electronic destination signs are blanked at the end of the timetable (eu07/maszyna#446),
- horns need the air or the voltage to sound (eu07/maszyna#290, #76): HornType=[Pneumatic]|Electric and
Horn3Type in Cntrl.; a pneumatic horn needs 0.2 MPa in the main reservoir (or the main pipe without one),
an electric one the low voltage; the lever stays where it was put,
- compressor start delay (#67): CompressorStartDelay [s] in Brake., counted from the compressor getting its
power, after the engine starts say; none by default,
- the channel and volume buttons of a radio without power do nothing (eu07/maszyna#429); the power check of
the radio is TMoverParameters::RadioPowered(),
- a lever moved smoothly sounds the positions it passes (#83).
Sonar findings in the functions changed: nesting, nested conditionals, commented-out code, std::format,
references to const. Unit tests: test::pair for two vehicles running into each other, test_couplers,
test_horn, test_wheelslip, test_compressor, test_radio, test_gauge_positions.
* fix: review findings of PR 217
- the pressures of the mover are in bar (MinCP=7.0 in the vehicle definitions), so the 0.2 the pneumatic horns
needed was 0.2 bar; it's 2 bar now, and the tests take their pressures in bar too,
- the lamps of the ground relay and of the motor overload relays follow the pressure switch as the line
contactors one does, TMoverParameters::MainCircuitLampsEnabled(), so the lamps of one cab go out together,
- the joint oil and fuel pump switch leaves out a pump started automatically, which ignores the switching:
with one, it couldn't turn the other off, and showed off with both running (OilFuelPumpsEnabled()),
- the kind of the train heating switch comes from the occupied vehicle on entering the cab too, as in the
switch commands; in a multiple unit these are different vehicles,
- CouplerForce() put the force taken back by the other vehicle on its far coupler when the vehicles faced each
other (Couplers[1 - End] rather than the coupler it's coupled with),
- the velocity difference along the coupler axis computed once, CouplerVelocityDifference(), for CouplerForce()
and CollisionVelocity(),
- the attachcoupler flag added without the SetFlag() call with 0, the index of the mirror moves noted as by side.
Tests: the coupler force of vehicles facing each other, the joint switch with an automatic pump, the lamps of
the main circuit, the horn and compressor pressures in bar.
* fix: coupler force of vehicles facing each other taken back along the other vehicle's axis
CForce runs along the axis of its own vehicle, so the force the other vehicle takes back on its coupler of the pair
is turned around once more when the vehicles face each other (-CF * DirPatch()), as that vehicle computes it itself.
Tests: the coupler forces of the pair facing each other and facing the same way.
* refactor(sonar): use override instead of redundant virtual (cpp:S3471)
* refactor(sonar): remove empty statements, one declaration per statement (cpp:S1116, cpp:S1659)
* refactor(sonar): drop redundant lambda return types (cpp:S3574)
* refactor(sonar): prefer using over typedef (cpp:S5416)
* refactor(sonar): use =default for trivial special members (cpp:S3490)
* refactor(sonar): use nullptr literal (cpp:S4962)
* refactor(sonar): remove redundant access specifiers (cpp:S3539)
* refactor(sonar): remove redundant casts (cpp:S1905)
* refactor(sonar): use std::scoped_lock instead of std::lock_guard (cpp:S5997)
* refactor(sonar): construct elements in place with emplace_back (cpp:S6003)
* refactor(sonar): make narrowing conversions explicit (cpp:S5276)
* refactor(sonar): mark unused parameters (cpp:S1172)
Unused names are commented out; parameters used only on some platforms
are marked [[maybe_unused]].
* refactor(sonar): declare non-mutating member functions const (cpp:S5817)
Virtual functions are left untouched so overrides keep matching.
* refactor(sonar): merge collapsible nested if statements (cpp:S1066)
Comments that preceded the inner if are kept above the merged statement.
* refactor(sonar): scope single-use variables in if init-statements (cpp:S6004)
* fix(sonar): give polymorphic base classes virtual destructors (cpp:S1235)
* refactor(sonar): use try_emplace for map insertion (cpp:S6030)
* refactor(sonar): use auto where the type is spelled out on the right (cpp:S5827)
* refactor(sonar): remove redundant parentheses (cpp:S1110)
* refactor(sonar): document intentionally empty functions (cpp:S1186)
* refactor(sonar): remove dead stores (cpp:S1854)
Side effects (e.g. LISTLINE++) are kept.
* refactor(sonar): remove unused variables, captures and private fields (cpp:S1481, cpp:S1068)
* refactor(sonar): use structured bindings for pair access (cpp:S6005)
* refactor(sonar): use range-based loops and ranges algorithms (cpp:S5566)
* refactor(sonar): split chained assignments (cpp:S1121)
* refactor(sonar): add default cases to switch statements (cpp:S3562)
* refactor(sonar): use std::size for array lengths (cpp:S7127)
* refactor(sonar): use std::ranges algorithms and std::erase(_if) (cpp:S6197)
* refactor(sonar): access static members through the class (cpp:S2209)
* refactor(sonar): add braces around nested if-else (cpp:S5261)
* refactor(sonar): avoid side effects inside typeid operands (cpp:S5279)
* refactor(sonar): drop top-level const from by-value return types (cpp:S5951)
* refactor(sonar): declare variables separately from their type definitions (cpp:S3646)
* refactor(sonar): declare loop counters in the for statement (cpp:S5955)
* refactor(sonar): rely on class template argument deduction (cpp:S6012)
* refactor(sonar): inherit base constructors instead of forwarding them (cpp:S5952)
* refactor(sonar): rename locals that shadow outer declarations (cpp:S1117)
Only local variables and definition parameters are renamed; shadowing
struct fields and enumerators in headers are left for a separate change.
* refactor(sonar): reduce enum qualification with using enum (cpp:S6177)
Applied only where no unqualified name in the block could be captured by
the introduced enumerators.
* refactor(sonar): mark converting constructors explicit (cpp:S1709)
sound_source and the gl::object conversion operators stay implicit; they
are relied upon by copy-list-initialisation and GL calls.
* refactor(sonar): initialise members in initialiser lists or declarations (cpp:S3230)
* refactor(sonar): make read-only local references and pointers const (cpp:S5350)
* refactor(sonar): take read-only pointer and reference parameters as const (cpp:S995)
TTrain command handlers keep their signature, it is fixed by the handler table.
* refactor(sonar): pass expensive-to-copy parameters by const reference (cpp:S1238)
Signatures declared in files touched by PR 206 (Driver.h, EU07.cpp) and
virtual overrides are left unchanged.
* refactor(sonar): use transparent comparators for string-keyed maps (cpp:S6045)
std::unordered_map instances and map types exposed in headers used by
other modules are left as they are.
* fix(sonar): do not use UI text as a printf format string (cpp:S5281)
Text lines containing '%' would otherwise be interpreted as format
specifiers by ImGui::TextColored.
* refactor(sonar): use std::bind_front for callbacks (cpp:S5995)
* refactor(sonar): drop const_cast on string literals passed to the Python C API (cpp:S859)
* refactor(sonar): take read-only string parameters as std::string_view (cpp:S6009)
The Windows messaging helpers keep std::string, they need c_str().
* refactor(sonar): make read-only global tables const (cpp:S5421)
Mutable global state (flags, timers, singletons) is left as is.
* refactor(sonar): replace single-case switch statements with if (cpp:S1301)
* refactor(sonar): format UUIDs and log timestamps with std::format (cpp:S6494, cpp:S5945)
* refactor(sonar): use std::array for local fixed-size arrays (cpp:S5945)
Arrays that are class members or part of headers are left unchanged.
* fix(sonar): test the bearing damage bit, not bit 0 (cpp:S872)
'DamageFlag & dtrain_bearing > 0' parsed as 'DamageFlag & (dtrain_bearing > 0)',
i.e. DamageFlag & 1, so bearing friction reacted to the wrong damage flag.
* refactor(sonar): assorted small fixes
- empty() instead of size() comparisons (cpp:S1155)
- member initialisers in declaration order (cpp:S3229)
- no redundant c_str() when a std::string is accepted (cpp:S7121)
- contains() on associative containers (cpp:S6171)
- const reference instead of a copying range-for (cpp:S6032)
- starts_with() for prefix checks (cpp:S6178)
- no std::move on temporaries (cpp:S5274)
- has_value() on std::optional (cpp:S7172)
- bool literals for bool members (cpp:S5820)
- inline only on the definition (cpp:S3548)
- explicit base access specifier (cpp:S5965)
- explicit element access instead of dereferencing an array (cpp:S7116)
- rely on the C++20 rewritten operator!= (cpp:S6186)
* refactor(sonar): more small fixes
- std::format instead of iostream manipulators in to_string/to_hex_str (cpp:S6495);
output verified identical, negative hex values keep the unsigned form
- remove an empty compound statement (cpp:S108)
- drop an always-false unsigned < 0 branch (cpp:S1768)
- explicit lambda capture (cpp:S3608)
- std::make_unique (cpp:S5950)
* chore: strip stray carriage returns left in TTrain constructor comments
* fix: keep quantize() in its own value type
The S5276 change cast the result of the generic quantize<Type_>() to
unsigned int, which truncated float/double callers (shadow angle slider,
editor rotation snapping, AI speed control steps) and broke negative values.
* fix(sonar): use integer loop counters in segment sampling (cpp:S2193)
* refactor(sonar): clean up issues reported on PR 209
- remove locals left unused after the dead-store cleanup (cpp:S1481, cpp:S1854)
- unnamed unused parameter (cpp:S1172)
- single-use declarations moved into if init-statements (cpp:S6004)
- auto for casted initialisers (cpp:S5827)
- const references and pointers where nothing is modified (cpp:S5350)
- rename structured bindings shadowed by inner declarations (cpp:S1117)
- Terrain work mode shows a browser of the textures folder in place of the
node bank; textures/materials can be dragged onto the palette entries
(replacing the material), the material field and the water material field
- Ctrl+Z/Ctrl+Y for heightmap terrain changes: a brush stroke or an
operation is one step of the editor history
- Ground conversion reads only the files of the terrain directives
(.txtf with origin/rotate, or .btf without text), paints the chunks with
the materials of the triangles, drops only the shapes of those files
- Fix: ground grids converted out-of-range floats to int, so whole-scene
queries returned the triangles of a single cell (shifted chunks)
- Fix: terrain layers copied from textures already uploaded without their
data stayed grey
- Fix: ImGui ID conflict between terrain tool radios and section headers
- Fix: layers of terrain .txtf files named with the scenery/ prefix and
could not be saved
- Editor selftest commands for the terrain
* Text displays: accept characters above 127, in windows-1250 or utf-8
A text display (sub-model of type "text") looks up the sub-model of each character
in a 256 entry table, and indexed it with a plain char. With char being signed, any
character above 127 gave a negative index: reading the text went outside the table,
and so did filling the table if a character sub-model had such a name. In effect the
displays could only show ASCII, and a text with national characters could crash.
The lookup is now keyed by unicode code point. Both the displayed text and the names
of the character sub-models are decoded as utf-8 if they are valid utf-8, and as
windows-1250 otherwise, so legacy (ansi) sceneries and models work next to utf-8
ones, and the two can be mixed. A short ansi text can be valid utf-8 by accident
(two upper case accented letters in a row will do); when both readings are possible
the one which finds more of its characters in the model is used.
The rest is unchanged: the first character of the text still isn't displayed, the
characters are still drawn in the translucent pass only. A missing text pointer no
longer gets dereferenced.
* Text displays: prepare the characters once for each text
The sequence of character sub-models was cached for the last text only, so
displays of several instances drawn in turn decoded their texts again on
every draw. It is now kept for each text the display shows; the texts of the
instances don't change, so a draw costs a single lookup.
Also the comments added in the renderers are now in English.
* Text displays: move the text decoding to utilities
utf8_to_utf32() and win1250_to_utf32(), with the windows-1250 table, now sit
next to win1250_to_utf8(). The existing function maps only the Polish letters
and passes other bytes above 127 through, so it can't serve the displays.
* Text displays: address the SonarCloud findings
std::array instead of the C-style arrays, the utf-8 sequence length worked
out in a function of its own instead of nested conditional operators,
std::byte for the bit operations, std::ranges::count_if and contains().
The character loop of the renderers moved to Render_Alpha_text(), which
takes the nesting back to the limit, and the static pasText is accessed
through the class.